Differences

This shows you the differences between two versions of the page.

--- kvalobs:kvoss:system:qc2:test:vm101notes [2010-06-24 22:47:53]
paule
+++ kvalobs:kvoss:system:qc2:test:vm101notes [2022-05-31 09:29:32] (current)
@@ Line 1: / Line 1: @@
-====== Installation and test on dev-vm101 notes [kvqc2_1.0.1] ======
+====== Installation and test on dev-vm101 notes [kvqc2_1.0.1 and other revisions ... ] ======
 The following notes describe the installation and use of **kvqc2 version 1.0.1** Sources: https://svn.met.no/viewvc/kvoss/kvQc2/branches/kvqc2-1.0.1/
@@ Line 14: / Line 14: @@
   * Log into dev-vm101 as user kvalobs
-  * If an old kvqc2 exists stop the running kvqc2 process {e.g. use kvstop ? terminate the process pid ?}
+  * If an old kvqc2 exists stop the running kvqc2 process by 'kvstop -l' (lower case L), then type the number corresponding to kvqc2
   * Remove active configuration files (this is to just ensure that when the new kvqc2 version is set running it does not find and use an old configuration file)
@@ Line 49: / Line 49: @@
 Setting up kvqc2 (1.0.1-1) ...
 paule@dev-vm101:~/kvqc2-1.0.1$
+</code>
+**Bug Fix and Confirmation of apt-get install**
+Initial tests illustrated that some data was written back to thedatabase at too high a precision. This is fixed in revision 1782: https://svn.met.no/viewvc/kvoss?view=rev&revision=1782 and led to a kvqc2-1.0.2 revision. This also provided the opportunity to check that the install from apt-get install works, i.e.:
+<code>
+paule@dev-vm101:~$ sudo apt-get install kvqc2
+Reading package lists... Done
+Building dependency tree... Done
+The following packages will be upgraded:
+  kvqc2
+upgraded, 0 newly installed, 0 to remove and 78 not upgraded.
+Need to get 288kB of archives.
+After unpacking 0B of additional disk space will be used.
+Get:1 http://repo.met.no etch/main kvqc2 1.0.2-1 [288kB]
+Fetched 288kB in 0s (12.7MB/s)
+(Reading database ... 52403 files and directories currently installed.)
+Preparing to replace kvqc2 1.0.1-1 (using .../kvqc2_1.0.2-1_i386.deb) ...
+Unpacking replacement kvqc2 ...
+Setting up kvqc2 (1.0.2-1) ...
+paule@dev-vm101:~$
 </code>
@@ Line 286: / Line 308: @@
 **NB** Lots of work to be done tuning the control flag settings etc!!! :-)
+**NB** Currently only work on data where "qclevel NOT EQUAL 0" **Therefore it is vital that a qc1 algorithm has checked the data ... otherwise there will be no Qc2 check** suspect that this might be the case. How often? How better to tune?
 ==== Further testing ====
@@ Line 400: / Line 424: @@
 </code>
-{{:kvoss:system:qc2:test:output.jpg|}}
+{{kvalobs:kvoss:system:qc2:test:output.jpg|}}
+More examples of other parameters available at:
+^https://kvalobs.wiki.met.no/doku.php?id=kvoss:system:qc2:test:algorithms:singlemissingpoint^
--O More to follow ???
  --- //2010/06/22 23:25//