Differences

This shows you the differences between two versions of the page.

--- kvalobs:kvoss:system:qc2:test:acceptance:qc2opecfg [2010-03-24 23:29:30]
paule
+++ kvalobs:kvoss:system:qc2:test:acceptance:qc2opecfg [2022-05-31 09:29:32] (current)
@@ Line 2: / Line 2: @@
 This is a set of tests to check the operation of the configuration files and become familiar with setting different options.
 **Prerequisite**
   * Stop kvalobs with bin/kvstop (rationale: run kvQc2 from the terminal to immediately analyse output)
+**NOTES**
+  * For dev-vm116 local installation $PREFIX=/metno/kvalobs
+  * For debian package it is probably: $PREFIX=
 ^Step ^Direction ^Expected Result ^Pass/Fail Criteria or Comment ^
-|001 |cd $KVALOBS. Make a copy of the existing Qc2Config directory  | -- | -- |
+|001 |Locate the active Qc2Config directory. Make a copy of the existing Qc2Config directory  | -- | -- |
+| |$ cd $PREFIX/etc/kvalobs | -- | -- |
 | |$ tar cvf Qc2Config.tar Qc2Config/| -- | -- |
 | |Remove the Qc2Config directory. | -- | -- |
 | |$ rm -r Qc2Config| -- | -- |
-|002 |Run kvQc2 | -- | -- |
+|002 |Run kvQc2 as follows: | -- | -- |
-| |bin/kvQc2 |Does not exist: /metno/kvalobs/Qc2Config/ | -- |
+| |$ bin/kvQc2 |Does not exist: $PREFIX/etc/kvalobs/Qc2Config/ | -- |
-| |Note: open a new shell to perfomr the following tasks and monitor the results in the bin/kvQc2 program output. | -- | -- |
+| |Note: **open a new shell to perform the following tasks** and monitor the results in the bin/kvQc2 program output, i.e. set up two shell windows side by side, one with kvQc2 running, the other with the modifications to the Qc2Config directory. The program will attempt to scan for a configuration file every 59s and a response is detected as described below. | -- | -- |
-|003 |mkdir Qc2Config | Scanning For Files ;/metno/kvalobs/Qc2Config/ | -- |
+|003 |$ mkdir Qc2Config | Scanning For Files ;$PREFIX/etc/kvalobs/Qc2Config/ | -- |
-|004 |touch Qc2Config/example.dat | -- | -- |
+| | **Note** kvQc2D scans the Qc2Config directory every ~60s, therefore wait at least this time between steps to check for results|||
-|005 |Run kvQc2 | -- | -- |
+|004 |$ touch Qc2Config/example.dat | - no response - | -- |
-|006 |Run kvQc2 | -- | -- |
+|005 |$ touch Qc2Config/example.cfg| --  | -- |
+| |Configuration File Found: $PREFIX/etc/kvalobs/Qc2Config/example.cfg; 2010-03-24 23:35:31: 2010-03-24 23:00:00 -> 2010-03-24 23:00:00  $PREFIX/etc/kvalobs/Qc2Config/example.cfg|||
+| | | The times are default times generated if no times are set specifying the start and stop of the algorithm run. ||
+|006 |View https://svn.met.no/kvoss/kvalobs/trunk/src/kvQc2/Reference/ProcessUnit.cfg in a browser and review contents. | Note the paramter Last_NDays=3 is set. | -- |
+| |Copy the file to the Qc2Config directory,e.g.: | | |
+| |$ wget https://svn.met.no/kvoss/kvalobs/trunk/src/kvQc2/Reference/ProcessUnit.cfg  |Note the start and end time now covers the last 3 days. | |
+| |2010-03-24 23:54:34: 2010-03-21 23:00:00 -> 2010-03-24 23:00:00  $PREFIX/etc/kvalobs/Qc2Config/ProcessUnit.cfg |||
+|007 |Edit the ProcessUnit.cfg file  by replacing Last_NDays=3 (a # may be used to comment out) with:| --  | -- |
+<code>
+#Last_NDays=3
+#[Time Range]
+Start_YYYY=2007
+Start_MM=5
+Start_DD=31
+Start_hh=6
+Start_mm=0
+Start_ss=0
+End_YYYY=2007
+End_MM=12
+End_DD=31
+End_hh=6
+End_mm=0
+End_ss=0
+</code>
+|007 |Observed result: | --  | -- |
+| |2010-03-25 00:00:28: 2007-05-31 06:00:00 -> 2007-12-31 06:00:00  $PREFIX/etc/kvalobs/Qc2Config/ProcessUnit.cfg    |||
+The full list of available configuration file options is found [[kvoss:system:qc2:user:config_summary|here]], experiment!
+|008 |Remove Qc2Config directory and replace original: | --  | -- |
+| |$ rm -r Qc2Config    |||
+| |$ tar xvf Qc2Config.tar   |||